Guillotineschaar – Plate Shear - Mechanical KAPEMA SMP 20-30

Advertentie ID: M81118
Prijs op aanvraag
Verzend verzoek
Afbeeldingen
Kaart
Plate Shear - Mechanical KAPEMA SMP 20-30 - om tweedehands te kopen/uploadpic/tramaofinal_inserat/bilder/81118/bild1.jpg,/uploadpic/tramaofinal_inserat/bilder/81118/bild2.jpg,/uploadpic/tramaofinal_inserat/bilder/81118/bild3.jpg,/uploadpic/tramaofinal_inserat/bilder/81118/bild4.jpg,/uploadpic/tramaofinal_inserat/bilder/81118/bild5.jpg

Locatie artikelen

Auslieferungslager Germany

Fabrikant

KAPEMA

Beschrijving

sheet width 2050 mm
plate thickness 3 mm
strokes per minute until 35
cutting angle 2,0 °
table height over floor 870 mm
thickness at "Niro-steel" 2 mm
total power requirement 4 kW
weight of the machine ca. 1550 kg
range L-W-H 2,5 x 1,57 x 1,21 m
sheet width 2050 mm
plate thickness 3 mm
strokes per minute until 35
cutting angle 2,0 °
table height over floor 870 mm
thickness at "Niro-steel" 2 mm
total power requirement 4 kW
weight of the machine ca. 1550 kg
range L-W-H 2,5 x 1,57 x 1,21 m
sheet width 2050 mm
plate thickness 3 mm
strokes per minute until 35
cutting angle 2,0 °
table height over floor 870 mm
thickness at "Niro-steel" 2 mm
total power requirement 4 kW
weight of the machine ca. 1550 kg
range L-W-H 2,5 x 1,57 x 1,21 m
sheet width 2050 mm
plate thickness 3 mm
strokes per minute until 35
cutting angle 2,0 °
table height over floor 870 mm
thickness at "Niro-steel" 2 mm
total power requirement 4 kW
weight of the machine ca. 1550 kg
range L-W-H 2,5 x 1,57 x 1,21 m
sheet width 2050 mm
plate thickness 3 mm
strokes per minute until 35
cutting angle 2,0 °
table height over floor 870 mm
thickness at "Niro-steel" 2 mm
total power requirement 4 kW
weight of the machine ca. 1550 kg
The new motor guillotine type SMP is a well dimensioned machine with
all-welded link guides. The drive takes place with a
Standard geared brake motor via a chain connection to the main axle. the
Knives are of the highest quality. The optimal cutting angle secures the
Together with the rubber-covered blank holder perfect cuts.
Bearings and guides are maintenance and lubrication-free.
Standard equipment: • Back gauge 665 with mm scale. •
cutting edge lighting. • Section counter. • Table extensions 600 mm. •
Right angle stop, left. • Movable 24 V foot switch with emergency stop.
• Motor protection switch and emergency stop. • 2 cutting edges per knife. •
Rear protective grille, warranty = 12 months for single-shift operation.
Other models: 1275 x 3mm, 1250 x 4mm, 2050 x 2mm
Machine dealer with own stock of 1600 m².
The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Toestand

Nieuw en ongebruikt

Bouwjaar

Fabrikneu / new

Machine onder stroom

Nee
Verzend verzoek

Aanbod van:

PLUM & Partner Werkzeugmaschinen GmbH

PLUM & Partner Werkzeugmaschinen GmbH
Winkelstraße 32
32257 Bünde

Contactpersoon: Andreas Plum

Verzend verzoek
Toon telefoonnummer
Tel.: +49 (0) 52 23 / 57 44 44
Bedrijfsprofiel weergeven



Andere interessante aanbiedingen in deze categorie Guillotineschaar

Plate Shear - Mechanical KAPEMA SMP 20-20
Guillotineschaar – Plate Shear - Mechanical KAPEMA SMP 20-20

Prijs op aanvraag
Plate Shear - Mechanical KAPEMA SMP 12-30
Guillotineschaar – Plate Shear - Mechanical KAPEMA SMP 12-30

Prijs op aanvraag
CO